Відео

Does the 2” pipe fit through the axle guides? (The plastic ramps inside the tubes that align the axle into the seals$

Have you sold the material? Or just used it for yourself

Very helpful, thank you

How many miles does this new battery last for? I just did the same swap with a Agomola 36v 20ah battery.

Not one needle lost.. impressive

Great tank god bless you

Thank you !

Hi everyone what is the part number to that needle bearing by chance ?

What about the Oring that comes with em from spicer?

Ty 4 this video....👍😎🇺🇸😇

Thanks for taking the time to explain clearly all the details

Great start to finish with details .

Does this spin when you unlock the wheel and leave it in 2 wd? I have this issue but im wondering if i can temporarily tie wrap this thing down front clacking and just drive 2wd for the time being.

Awesome video. Showed me exactly what I needed to know. Thank you brother

@Ventures Truck Parts, I accidentally put a Dana 50 axle into a Dana 60 front diff. We'll, one side, anyway... The driver's side wouldn't go in far enough, which raised the alarm bells. That's when I notices the difference in axle size/splines. So, the passenger side has the 50 installed, and I beat the piss out of the driver's before stopping and putting the 60 back in. My question is, what was I beating the axle shaft against inside the diff when trying to get the shaft to seal? Could I have done damage internally?? And how about the wrong shaft fitting into the passenger side??? Will it JUST not engage properly, or is damage already likely done???? Switching to the Dana 60 axle asap, btw...

Great video

This is the only thing that worked after trying so much bullshit

Is there different hubs for autolockers ?

Thanks for not making this video 10min long. I just needed to know the flathead screwdriver pop off bit. To the point no mucking around. I appreciate it 👍

ford dealer parts told me cant get the black hub o ring or the selector switch (plastic on/off outer switch part, it does come out but theres a trick, move it to between c and k in "lock") v groove oring unless you buy a new locking hub assmbly. I could prob source one but today there is no American made legendary quality company oring kit anymore. If anybody knows of one still left, please let me know.There is a bearing inside as well, anybody know if there are any numbers on the bearing ?

Thanks I will look and see .

I am looking at your website and found these front outer hub/shaft bearings so great stuff, my next quest. is, these are the outer, is there a front inner hub/shaft bearing ?

@ 9:48, you saying that we can take this hub bearing out ? I was under the impression that you could only buy the whole hub ? if so you got any dana/spicer officials or OEM ?

Well done… excellent video.

Part number please.

Does this work for a 450 super duty?

More like 99.5-04

It will only go together one way

So 06 f350 doesn't need thrust washers?

My 2000 excursion 4x2 7.3 diesel making a thump noise when braking

What if you just put some grease on your fingers and put them in the tube to hold the axle up and then just slide your fingers out when you’re close enough….

This is a w4 1770

Now weld them up.😉

I don't usually comment on these videos, but I must say This was super good. Thank you for posting this. I've got a bad upper ball joint and was scratching my head how the axel comes out. Again thank You!! Edit... My darn vaccum and axel did not come out as easy as yours!! cut my behind, but at least I felt confident how it is supposed to come out.

Thx dear

How do you remove the main baring in the hub Assembly ?

Very clear, Thanks. I love my 99 F250 super duty and have heard a lot of good things about the Dana axles

I have a 2020 450 with a bent driver side axle tube. Will a 2012 450 axle assembly fit even if I have to swap gears over?

Great video

Excellent detail in your videos.

My 04 F350 hub looks nothing like that. 😅

What is the part # for this wheel hub?

Excellent video. Videos like this are extremely helpful when working on something new to you. 👍👍

💰💰💰💰💰

Very good video dude straight to the point i like it awesome job keep em up im subscribing for sure

Nice vid

3 months ago I put a entire brand new front end under my 2000 F-350 7.3l and I did it with watching and learning from you guys. Thank you so much for sharing your knowledge 🙏 👍👍 Jay.

What kind of grease?

Bonjour j ai un moteur hatz 2 cylindres je trouve pas mon préchauffage dessus ?

wait so that seal doesnt go all the way into that axel end to block the entry? you just left it dangling there..